|
Seagate ST3320833A Data Recovery Details
Seagate drives fail and the ST3320833A is no exception to this.
   
My computer couldn't start properly as the hard disk was clicking several times and, eventually, power was shutting down each time after I was trying to put the computer on. I decided to replace the computer a few days ago but now, I'd like to recover the content of the hard disk. The model number is Seagate(ST3320833A).
Ryan G
Belfast, Wales
Seagate is the world's largest and oldest manufacturer of computer hard disks. The company has been going from strength to strength with its $1.9 billion acquisition of rival hard drive firm Maxtor in 2006. Segates flagship desktop Barracuda 7200.11 drives, in particular the 1TB - ST31000340AS units, are failing at an alarming rate and prompting outrage from their faithful clients. A new self-bricking feature apparently resides in faulty firmware microcode which will rear its ugly head sometime at boot detection. Essentially the drive will be working as normal for a while, then - out of the blue - it’ll brick itself to death. The next time you reboot your computer the drive will simply lock itself up as a failsafe and won’t be detected by the BIOS. In other words, there’s power, spin-up, but no detection to enable booting. We have the fix for this issues without the need to open the drives up.
Common Seagate Hard Disk issues include, Seagate Momentus - can suffer premature media damage; Seagate U series - can suffer motor damage; Seagate Cheetah - Firmware corruption is No1 issue; Seagate Barracuda - Suffer from firmware, motor and read/write head issues. Seagate - ST3320833A. Recover data from broken RAID 1 array drive. The server had a power surge and the raid controller card is dead. All this happenned just before I was going to create a hotspare after one of the hard drives in the RAID 1 array failed. This means that I am left with no parent RAID controller and a lot of precious data to be recovered.
..John Reid, Birmingham, UK
Seagate hard drives are vunerable to a power surge or spike. As is the case with other hard disk's Seagate drives controller board is usually the weak spot that will fail. The controller board of most drives stores unique adaptive data that can only be associated with the drive that it was originally a part of. In other words, it's very seldom that you can just swap out a controller board from one drive to another and get the dead drive functioning again. In more cases than not the spindle motor controller driver (SMOOTH chip) on the logic board gets burnt. If this occurs the computer would shutdown completely, you would also normally notice a burning smell and when powered on the drive will not spin up at all.
If a drive is not spinning at all this can mean that there is a seized motor or indicates possible platter damage. Data recovery in this case involves opening the hard disk in a clean facility to work on the drive internally.
The computer will boot into the auto-detecting BIOS screen and freeze up. I cannot even enter the setup in BIOS or boot menu to change my boot device. I uninstalled the drive and changed my boot devices, but it still freezes up after connecting the SATA drive. I know the hard drive is causing the boot problem. I suspect is might have got a virus.Seagate, p/n: ST3320833A.
..Terry Rose, Essex, UK
The last typical Seagate hard drive issue applies also to all other hard drive makes and models, the problem is called bad sectors. After some period of time the platters were the data is located starts to degrade and bad sectors appear.
Whenever the hard drive attempts to read bad sectors it could start freezing, scratching, ticking and sometimes loud clicking. This leads to further damage to the surface and causes more data loss. As soon as you start experiencing such symptoms while reading important files, stop the drive immediately and consider sending it to a data recovery company like ourselves for a free diagnostic. Any further attempts to read the Seagate drive would just add up to the problems and make more data unrecoverable. In our Data Recovery Lab we use expensive imaging tools that are capable of force reading bad sectors from Seagate Hard Disks. This is usually the only way to effectively retrieve data from these Drives.
The last typical Seagate hard drive issue applies also to all other hard drive makes and models, the problem is called bad sectors. After some period of time the platters were the data is located starts to degrade and bad sectors appear. Whenever the hard drive attempts to read bad sectors it could start freezing, scratching, ticking and sometimes loud clicking. This leads to further damage to the surface and causes more data loss. As soon as you start experiencing such symptoms while reading important files, stop the drive immediately and consider sending it to a data recovery company like ourselves for a free diagnostic. Any further attempts to read the Seagate drive would just add up to the problems and make more data unrecoverable. In our Data Recovery Lab we use expensive imaging tools that are capable of force reading bad sectors from Seagate Hard Disks. This is usually the only way to effectively retrieve data from these Drives.If you experience any of the symptoms described above with your Seagate ST3320833A please call us on +44 (0) 2890 961976. If you hear your Seagate ST3320833A hard drive making some other unusual noises please call us on +44 (0) 2890 961976.
|
